VEMS gives you the full engine control that you need to bring out the best performance from your turbo/supercharged or normally aspirated engine. It has been developed by motorsports enthusiasts to provide other enthusiasts with a complete system with features only found in the more expensive 'high end' engine management systems.

VR to Hall Converter

Published in

$23.00

An (LM1815) VR to HALL interface and a (HC4024) counter chip in a small DSUB9 connector housing.

  • Requires 5V supply (from the assembled v3 controller EC36/28 pin, or other source, only appr. 10mA needed)
$23.00

Borg Warner AirWerks S363 Turbo


$810.00

Borg Warner turbo part number 177283.

63mm inducer extended tip compressor wheel, surge control grooves, 4" (101.6mm) Compressor inlet, 3" (76.2mm) Compressor outlet.

76mm turbine inducer, 68mm turbine exducer, 0.88 A/R turbine housing.

320-800hp range

$810.00

VW/Audi Coil Plug Kit

Published in

$15.00

A kit of 4 connectors to replace broken/damaged connectors or use Audi coils on another engine.

4 pin connector for VAG active COP
1J0 973 724 replacement connector housing + receptacles + small rubber-seal + rubber boot for VAG 06B905115R or 06B905115L COP "active-coil" (coil on plug ignition transformer).

$15.00

AWD Dyno


To start out 2012 right, we have a new Land and Sea AWD Hub dyno to tune your 2wd or AWD car.

Presenting Vermont’s first absorbing dynamometer and first AWD dynamometer.

With our state of the art Land and Sea hub dyno we can tune your car for its best potential.

Dyno-only Rates:
Baseline - $100 2wd, $125 AWD
2wd hourly - $125
AWD hourly - $150
For half or full days, contact us.

Tuning (in addition to dyno rates if dyno tuning):
VEMS Tuning - $75/hr

Bosch 17014 Wideband O2 Sensor

Published in

$79.00

Bosch wideband sensor for precision measurement of the amount of oxygen left over after combustion. Use as a replacement sensor or with a new system.

$79.00

6mm EGT Sensor

Published in

VEMS 6mm EGT sensor
$76.00

Fast acting due to small tip size, but extremely durable due to 6mm body. Perfect for turbo applications.

This sensor is manufactured specifically for VEMS and not available elsewhere.

Comes with 1/8" NPT stainless steel fitting for ease of installation. You can either add a 1/8" NPT bung or weld this right to the exhaust. Typically placed pre-turbo for best results or right at the exhaust port or collector for non-turbo applications.

$76.00

Siemens 60lb HighZ Injector

Published in

$55.00

Siemens high-impedance (12.6ohm) injector.
L107 Siemens / Mototron Deka 4 (Flow-Matched sets to 1%)
length: 64mm between O-rings (middle to middle)
other names: Siemens FI114961 - Mototron INJ-GAS-006 - Accel 74620L - MSD/Edge 2030

Static Flow Rate at different fuel pressures:

60lb/hr (sometimes called 63 lb/hr). For estimations: with BSFC=0.5lb/(HP*hr) this means 120 HP/cylinder at 100% duty. You want to apply your estimated BSFC, max duty and add some margin. Also note that BSFC is higher with Ethanol based fuels like E85.
630cc/min @ 3bar (=300kPa = 43.5 psi)

$55.00

Econoseal / JPT Crimptool

Published in

Econoseal/JPT Crimptool
$55.00

Those who make their own harness looms (crimp wire to Econoseal or WBO2 or injector recepticles), will probably want one.
This tool supports 3 wire sizes with it's installed head (removable head), the smallest jaw marked 0.5 .. 1 mm2 is suitable for Econoseal and JPT (WBO2, injector, and many other connectors). The biggest jaw is good for common size relay and fuse connections.

$55.00

EV1 Injector Connector

Published in

$3.50

2 pin C-type (with clips) AMP Junior Power Timer connector, commonly used for injectors and sensors (eg. manifold or intake air temperature, and coolant temperature, or transmission reed relay or back-up-light switch) or actuators (like idle air valve).

The connector is black and includes receptacles, boot and small rubber seals (proper, one wire seal capable connector).

$3.50

Siemens 80lb HighZ Injector

Published in

$60.00

Siemens 110324 injector high-impedance injector.
length: 59.35mm between O-rings (middle to middle).
New style, all plastic, fully compatible with Siemens 60lb/hr

Flow Rate: 840-850cc/min @ 3 bar (= 300 kPa = 43.5 psi). 80LBS/HR
Flow Rate: 970-981 cc/min @ 4 bar (=400kPa = 58 psi)
Resistance: 12-16 Ohms (series power resistor not needed)

Available with either the standard Bosch EV1 connector or the "USCar" EV6 connector.

$60.00
Syndicate content